KSResin Epoxy Specs — Coverage Rates, Mix Ratios & Prices
KSResin epoxy products compared: published coverage rates, mix ratios, thickness caps, recoat windows and official prices — every figure cited with a Last Verified date.
Quick answer
KSResin sells 2 epoxy products, with published coverage figures from 26.1 to 26.1 sq ft/gal. Every figure below traces to an official KSResin source; anything unpublished is marked rather than estimated.
Manufacturer datasheet · 2026-11-06KSResin publishes no coverage chart — a fact we state rather than paper over. Where a brand omits the number, this site applies the labeled theoretical baseline (the 1604 rule) instead of inventing one, and the spec tables below carry everything the brand does publish: mix ratios, thickness caps, recoat windows and prices, each with its source.
KSResin KSResin Liquid Stone Elite
Published coverage (status column shows published vs derived-from-official-calculator):
| Coat / basis | Thickness | Rate | Status |
|---|---|---|---|
| coating (calculator basis) | 0.0625" | 26.1 sq ft/gal | derived — official calculator basis 0.034 fl oz/sq-in ≈ 1/16" coating → 1 gal ≈ 26.1 sq ft at 1/16" (derived from official formula, not a published chart) |
No published sq-ft chart; figure derived from the brand's own official calculator formula, marked derived.
Specs (official sources):
| Spec | Value |
|---|---|
| Mix ratio | 1:1 by volume |
| Recommended coat | 0.125" |
| Max single pour | 0.125" — max coating 1/8"; max casting 1/4" |
| Recoat window | 3–6 h tacky chemical bond; or 24 h + 220-grit sand for a mechanical bond |
| Price | $110 per 1 gal kit ($110/gal) — official product page variants (checkout source) (dual) |
| Typical uses | bartops, tabletops, countertops, end tables |
KSResin KSResin Liquid Cast Deep Pour
Coverage: No coverage figures (casting resin; official calculator is volume-based L×W×depth).
Specs (official sources):
| Spec | Value |
|---|---|
| Mix ratio | 1:1 by volume |
| Recommended coat | 2" |
| Max single pour | 2" — designed for 1/2"–2" layers (most pours 1/2"–1"), max 2" per layer |
| Recoat window | No published recoat window; layered pours in 1/4" increments with degas pauses per official instructions |
| Price | $105 per 1 gal kit ($105/gal) — official product page variants (checkout source) (dual) |
| Typical uses | flower preservation, encapsulation, charcuterie boards, deep molds |
Sources & verification
Captured 2026-11-06. WAF-protected pages were read from official archived snapshots or the brands' own Shopify/Zendesk endpoints — every quote still traces to an official KSResin channel, with the access route noted where relevant. Full per-verbatim collection records live in this site's data file.
- https://www.ksresin.com/products/liquid-stone-elite-countertop-epoxy-resin
- https://www.ksresin.com/pages/epoxy-resin-calculator
- https://www.ksresin.com/products/liquid-cast-deep-pour
Use the numbers
- Coverage calculator — pick the KSResin product, enter your area, get gallons with this rate.
- Cost calculator — the same job priced against every other brand.
- Mix ratio calculator — exact Part A/B splits at 1:1.
How to read these tables
Three habits make spec sheets comparable instead of confusing. First, read the coverage rows before the price rows: a cheaper per-gallon price on a product that covers less ground can be the more expensive pour, and the calculator above is the honest tiebreaker. Second, treat the thickness caps as hard limits, not suggestions — a coating product pushed into casting depth fails from the inside out, by heat, hours after the pour looked fine. Third, check the recoat window against your actual schedule: a 3-hour window means the second coat goes on the same afternoon or not at all without sanding, and a day-long deep-pour window means a weekend, not an evening. Every value above keeps its source and verification mark so those trade-offs can be argued with data — and where a row reads "(to be verified)", it means the brand does not publish the figure, not that we skipped it.
FAQ
What coverage does KSResin publish?
The published figures are in the tables below with their sources — use them for KSResin products before the theoretical baseline. The [coverage calculator](/epoxy-coverage-calculator) switches rates automatically when you pick a KSResin product.
Where do these KSResin specifications come from?
Every figure is captured from KSResin's own published material — official product pages, TDS documents and help-center articles — with the source link shown under each table and a Last Verified date (2026-11-06). Where the same figure appears on two official pages it is marked dual-verified.
Is KSResin the best epoxy for my project?
Size the project first — area and thickness through the [coverage calculator](/epoxy-coverage-calculator) — then compare candidates on the specs that matter for your job: max coat thickness for builds, recoat window for schedules, and the price per gallon from the [cost calculator](/epoxy-cost-calculator). "Best" without a project is marketing.
All brands
